Makullin jigilar jigilar gel liner mai rataye tare da Dala
| Sunan samfur | Lebur mai rataye gel liner makulli tare da Dala |
| Abu NO. | P498-P |
| Kayan abu | Aluminum |
| Nauyin samfur | 310g ku |
| Siffofin Samfur | Na'urar kayan aiki mai laushi, aiki mai shiru;Maɓallin sakin dakatarwar gefe mai dacewa;Daidaita kulle Pin kyauta na iya rage aiki; nauyi - 100 kg;Jikin kashin baya da aka gina a ciki. |
| Aikace-aikace | Na'urar kulle nau'in Gear tare da jikin kashin baya |
| Launi | Baki |
Umarnin aikace-aikace
Makullin ALPS ne kawai za a iya amfani da shi a cikin Sockets Laminated na Al'ada.
NOTE:Ana iya amfani da makullin ALPS lokacin ƙirƙirar kwarangwal ɗin kwarangwal na ENDO.Idan kuna da niyyar ƙirƙira skeletal prosthesis na EXO, ana ba da shawarar ku yi amfani da Makullin ALPS. Idan kuna son ƙirƙirar soket ɗin thermoplastic ana ba da shawarar kulle ALPS.
Kada kayi amfani da kulle tare da kwasfa na thermoplastic.
RUWAN KWALLIYA
Lura: Yana da mahimmanci cewa lokacin da ake fitar da sabon soket tare da Makullin ALPS cewa za a yi tunanin majiyyaci akan layin da mara lafiya zai yi amfani da shi.
Gyara Samfurin Ingantacce
a.Shirya ingantacciyar ƙira ta hanyar da ake amfani da ita ban da ƙarshen nesa. Mai layin zai bar fitowa a lokacin matakin simintin gyare-gyare.
b.Rasp the protrusion don ƙirƙirar lebur tabo 1 3/4 inci diamita. Bugu da ƙari, wannan ɗakin kwana dole ne ya kasance daidai da layin ci gaba na soket. Nemo tsakiyar wannan yanki kuma a yi rami 3/8" kamar 1" zurfi.
Amfani da ALPS Fabrication Kit
a. Nemo mazugi na Alignment da aka samo a cikin ALPS Fabrication Kit FAB946.
b.Scuff lebur kasa na Alignment Cone da 80-100 grit sandpaper.
Ɗauki 5/16 ″*3 ″ Anchor Bolt(FKB-16) 5/16″*3 ″ Anchor Bolt (FKB-16) tare da man shafawa na silicone kuma a murƙushe shi a cikin Mazugi na Alignment har sai ya fito kusan 1/4 ″ sama da saman lebur.(Figure1)
d.Yin amfani da manne nan take, watauSuperglue, amintar da Mazugi na Alignment zuwa ƙarshen samfurin.e.Da zarar an saita, yi amfani da filasta don haɗa mazugi cikin Model. Cire duk wani abin da ya wuce gona da iri wanda ƙila ya faɗi akan mazugi na Alignment.
f.Cire Anchor Bolt kuma santsi samfurin don lamination.
Pre-Fabrication
a. Rufe wurin da aka yi amfani da shi kuma a yi amfani da jakar PVA ko jefa balloon a kan dukkan samfurin. Idan za a iya jawo jakar a kan Mazugi na Alignment, don haka jikin kulle ya rufe ƙarshen PVA, to, ba lallai ba ne a yi amfani da PVA. wannan ba haka lamarin yake ba, maiyuwa ka rufe jakar ka yi rami na samll don Anchor Bolt.
b. Gano wurin CLutch Dummy Plug wanda aka haɗa tare da Kit ɗin Kulle ALPS.
C.A shafa zaren Dummy Plug tare da man shafawa na silicone kuma a murƙushe shi da kyau a gefen ALPS Lock.
d.Kare ramin ko dai tare da tef ɗin abin rufe fuska ko ta tilasta guntun 5mm Pelite cikin ramin.
e.A shafa man shafawa na siliki a cikin mazugi mai karɓa na jikin ALPS Lock.
f.Coat da zaren 5/16 ″ Anchor Bolt tare da man shafawa na silicone sannan a daka jikin ALPS Lock zuwa Mazugi na Alignment.
g.Goge duk wani maiko da ya wuce gona da iri sannan a cika kan gunkin da yumbu ko miya.
h.A kula domin kada guduro ya ratsa ramin Anchor Bolt.Ƙwararren lamination na silicone yana da amfani a cikin wannan yanayin. Tape PVA kuma zai ba da kariya mai matsakaici.
